fujitsu scanner 5110c manual

3 Scanning Documents longer than A4 size(2)Page 58 CONTENTS 3.4 Saving Scanned Images in PDF Format(2)Page 61 Page 62 CONTENTS 3.4 Saving Scanned Images in PDF Format(5)Page 67 CONTENTS 3.6 Skipping blank pagesPage 75 CONTENTS 4.3 Cleaning the Inside of the Scanner (2)Page 77 1 2 3 4 5Page 79 CONTENTS 4.3 Cleaning the Inside of the Scanner (5)Page 80 CONTENTS 5 REPLACING CONSUMABLESPage 81 CONTENTS 5.1 Consumable and Replacement CyclePage 82 CONTENTS 5.1 Consumable and Replacement Cycle (2)Page 86 CONTENTS 5.2 Replacing the Pad ASSYINTRODUCTION 2. Page 87 CONTENTS 5.2 Replacing the Pad ASSY (2)Page 88 CONTENTS 5.3 Replacing the Pick RollerINTRODUCTION. Page 89 Caution. If you push up the pick roller tab using your fingernail, it may hurt or getPage 90 CONTENTS 5.3 Replacing the Pick Roller (2)Page 91 With the movie below, review the replacement procedure of the Pick Roller.Page 93 CONTENTS 6 TROUBLESHOOTINGPage 95 1 2 3Page 97 CONTENTS 6.1 Removing Jammed Documents(3)Page 98 CONTENTS 6.2 Error Indications in the Operator PanelPage 100 CONTENTS 6.3 Remedying Typical Troubles. INTRODUCTION This section describes troubles that may occur during scanning and how toINTRODUCTION Correctly connect.INTRODUCTION after you. Page 103 CONTENTS Symptom 3: The scanning does not start.Page 104 CONTENTS Symptom 4: Quality of scanned pictures or photos is not satisfactory.Page 105 CONTENTS Symptom 5: Quality of scanned text or lines is unsatisfactory.Page 106 CONTENTS Symptom 6: Images are distorted or blurred.Page 107 CONTENTS Symptom 7: Vertical lines appear in the scanned image.INTRODUCTION Do. Page 108 CONTENTS Symptom 8: The Function No.INTRODUCTION Does. Page 109 CONTENTS Symptom 9: Multi feed errors occur frequently.Page 110 If you cannot solve the problem afterPage 112 CONTENTS Symptom 11: Paper jams occur frequentlyPage 113 CONTENTS Symptom 12: The scanned images are elongatedINTRODUCTION For details on how.

• fujitsu fi-5110c manual, fujitsu scanner fi-5110c manual, fujitsu fi-5110c service manual, fujitsu scanner 5110c manual, fujitsu scanner 5110c manual pdf, fujitsu scanner 5110c manual free, fujitsu scanner 5110c manual software, fujitsu scanner 5110c manual downloads, fujitsu scanner 5110c manual 2017, fujitsu scanner 5110c manual online, fujitsu scanner 5110c manual instructions, fujitsu scanner 5110c manual 2016, fujitsu 5110c scanner manual.

Chapter 1 PREPARING THE. Page 4: INTRODUCTION INTRODUCTION. Thank you for purchasing the fi-5110C Duplex Color. Scanner. The use of a shielded interface cable. This document describes. Page 5 penetration of energy efficient computers and TrademarksThe program backs thePage 6 Manufacturer Symbols Used In This ManualPage 10: Chapter 1 PREPARING THE SCANNER Chapter 1 PREPARING THE SCANNERThe operator panel is located on the right side of. Page 12: Chapter 2 INSTALLATION OF THE SCANNER Chapter2 INSTALLATION OF THE SCANNERThis window is not displayed aou-Page 22: Appendix 1 TROUBLESHOOTING Appendix 1 TROUBLESHOOTINGScanner does not turn Have you pressed the power. Page 23 Symptom Check this item Remedy. Paper frequently multi Have the document requirements Use document conditions that meet thePage 25: Appendix 2 DAILY CARE Appendix 2 DAILY CAREPage 26: Appendix 3 REPLACING CONSUMABLES Appendix 3 REPLACING CONSUMABLES. Page 3 CONTENTS Regulatory InformationPage 4 CONTENTS Regulatory Information(2)Page 5 CONTENTS Regulatory Information(3)Page 6 CONTENTS TrademarksPage 7 CONTENTS Trademarks(2)Page 8 CONTENTS Note, LiabilityPage 10 CONTENTS Preface(2)Page 11 CONTENTS Preface(3)Page 12 CONTENTS Safety PrecautionsPage 13 CONTENTS Safety Precautions(2)Page 14 CONTENTS Safety Precautions(3)Page 15 CONTENTS Safety Precautions(4)Page 16 CONTENTS 1 NAMES AND FUNCTIONS OF PARTSPage 21 CONTENTS 2 BASIC SCANNER OPERATIONPage 22 CONTENTS 2.1 Turning the scanner ONPage 24 CONTENTS 2.2 Loading Documents on the ADF for ScanningPage 25 CONTENTS 2.2 Loading Documents on the ADF for Scanning(2)Page 30 CONTENTS 2.3 Scanning DocumentsPage 32 CONTENTS 2.4 How to Use the Scanner DriverPage 42 CONTENTS 2.4 How to Use the Scanner Driver(11)Page 43 CONTENTS 2.4 How to Use the Scanner Driver(12)Page 44 CONTENTS 2.4 How to Use the Scanner Driver(13)Page 51 CONTENTS 3.1 Scanning Double Sided Documents(2)Page 54 CONTENTS 3.3 Scanning Documents longer than A4 sizePage 55 CONTENTS 3.

Indicates that a device (hardware) alarm has occurred during scanning of documents. The screens and operations may differ slightly if the OS that you are using is other than Windows XP. Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in this chapter will differ slightly. The scanner is turned ON, and the green LED on the operator panel lights.If no operation is performed on the scanner for 15 minutes, the scanner automatically switches to the Power Save mode. Check the number of sheets in the document stack.For details on how to load documents, see 2. Start up ScandAll 21. This starts up ScandAll 21. 3. Select the scanner to be used. The following describes the procedure with examples of ScandAll 21 for ordinary scanning by using this driver software. You can save the changed settings as a Setting File. From next scanning, the settings are quickly changed by using these Setting Files.The following describes the procedure with examples of QuickScan for ordinary scanning by using this driver software. Scanning will be started according to the settings of the selected profile. The configuration window of ISIS driver appears. For example, if the document contains black text in a red frame and when the red color is selected, the scanner reads only the text and eliminate (drop out) the red frame. The screens and operations may differ slightly if the OS that you are using is other than Windows XP. Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in this chapter will differ slightly. For example, if the document contains black text in a green frame, you can set the scanner to read only the text and eliminate (drop out) the green frame. You can set the scanner to detect multi feed, stop scanner operation, and display an error message.The scanner monitors the length of documents. It detects a multi feed by changes in the document length when two or more document sheets are fed overlapping.

Page 114 CONTENTS Symptom 13 There is a shadow on the top and bottom edge of theINTRODUCTION. Page 115 CONTENTS 6.4 Items to Check Before Contacting the Agent Where You Bought thePage 116 Items to check before contacting the dealer where you bought the scanner. Check the following items before you contact the. Page 117 Feed system trouble. Meaning Findings. Document type. Main purpose of use. Last cleaning date. Value of ConsumablePage 119 CONTENTS 7 DOCUMENT SPECIFICATIONS FOR ADFPage 120 CONTENTS 7.1 Document SizeINTRODUCTION. Page 121 CONTENTS 7.2 Document QualityPage 124 CONTENTS 7.4 Area not to be perforatedPage 125 CONTENTS 7.5 Multi feed Detection ConditionsPage 126 CONTENTS 7.5 Multi feed Detection Conditions(2)INTRODUCTION 1 Image Processing Software. Page 129 CONTENTS 9 SCANNER SPECIFICATIONSPage 131 CONTENTS 9.1 Basic Specifications(2)Page 133 CONTENTS 9.2 Installation Specifications(2). This document describes how to handle fi-5110C Duplex Color scanner and basic operation methods. Before you start using fi-5110C Duplex Color scanner, be sure to thoroughly read this manual to ensure the correct use. Do not incinerate, crush, or shred the lamps or scanner parts. Do not breathe the chemical liquid contained in the scanner lamps. Do not connect to multiple-power strips. Use this scanner only at the indicated power voltage and current. Improper power voltage and current might cause fire or electric shock. Do not connect to multiple-power strips. Turn the scanner OFF if it is damaged. If the scanner is damaged for any reason, turn the scanner off and unplug the power cable. Contact the store where you purchased the scanner. Make sure that the scanner is installed on a flat, level surface and that none of its parts extend beyond the surface top, such as a desk or table. Do not install the scanner on unstable surfaces. When the scanner is not going to be used for a long period of time, be sure to disconnect the power plug from the power outlet.

Rotate the roller bushing by rotating it in the direction of the arrow. Reset the pick counter. When turning on the power, check that the scanner is connected to your PC.ATTENTION About troubles that are not described here, and the details of the errors,. HINT The Error Recover Guide is stored in Setup CD-ROM.When you encounter any alarm, turn off and on the scanner. If the alarm is still displayed on the Function No.Correctly connect power cable. You must use the AC adapter and cable supplied with your scanner by the manufacturer. The scanner operation is normal. Scanner operation is normal. Load document correctly on ADF paper chute. Close the ADF completely. Select halftoning or dithering on your Clean dirty locations.Clean dirty locations.Clean dirty locations.Back Does the Function No.Use documents that satisfy the requirements.Use the document that satisfy the requirements.Before you ask for repair service, please collect the following information. The label position is as below. Spec Description PA43400-D72201. The program backs the development and disse mination of products with functions that ef fec tively reduce ener gy consumption. About Maintenance The user must not perform repairs on this scanner. Do not install the scanner on unstable surfaces. Do not bloc k the ventilation por ts. Do not place heavy objects or c limb on top of the scanner. Firmly inse r t the po wer plug. Do not install the scanner in direct sunlight. Have you pressed the power button on. Push the power button in to turn the scan- ner. Are the AC cable and AC adapter properly connected to the scan- ner. Confirm that the document s meet the paper condi- tions for scanning. Before you start using fi- 5110C Duplex Color Scan ner, be sure to thoroughly read th is manual to ensure correct use. It is an open system in which business proprietors c an participate voluntarily. A v oid any contact when scanner i s in use.

Before you clean inside the scanner, turn off its power and unplug the AC adapter from the outlet. Wait for at least 15 minutes. Do not turn off the scanner when you clean the Feed rollers. To purchase the Cleaner F1, please contact the FUJITSU scanner dealer where you purchased the scanner. Remarks 1 bottle (100 ml) Moisten cloth with this fluid and wipe the scanner clean. Before you start to clean the inside of the scanner, disconnect the AC adapter from the outlet and wait at least 15 minutes to let the scanner cool down. ATTENTION Do not use water or neutral detergent to clean the inside of the scanner. CAUTION Be careful, the ADF may close and pinch your finger. Pad ASSY (x 1) Wipe the Pad ASSY (rubber surface) downwards. When cleaning the Pad ASSY, take care to prevent the cloth from catching on the metallic parts. Feed rollers (x 4) Clean lightly taking care not to roughen the surface of the rollers. Take particular care in cleaning the feed rollers since black debris on the rollers adversely affect the pickup performance. The screens and operations may differ slightly if the OS that you are using is not Windows XP. Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in this chapter will differ slightly. Do not use consumables and parts made by other manufacturers. To purchase the consumables, contact the FUJITSU scanner dealer where you purchased the scanner or an authorized FUJITSU scanner service provider. Parts Number Standard Replacement Cycle After 50,000 scans or one year. When turning on the power, check that the scanner is connected to your PC.Hold the left part of the shaft, and raise it to remove the shaft from the scanner while pulling the shaft to the left. Caution The Pick roller Bushing is hard. If you worry about that, push up the pick roller tab using a paper clip. Attatch the Pick roller to the scanner in reverse order of the procedure for removing. 10.

Safety PrecautionsNote, LiabilityWhile all efforts have been made to ensure the accuracy of all information in this manual, PFU assumesPFU further assumes no liability arising from the application orPFU disclaims all warranties regarding the information containedTrademarks. Safety PrecautionsPrefaceThis manual describes important details for ensuring the safe and correct use of this product. Thoroughly read this manual before you start to use this product. In particular, be sure to read andAlso, store this manual in a safe place so that it can be easily referred to during use of this product. Warning Indications Used In This Manual. This manual uses the following indications to ensure safe and correct use of this product, and toWarning. This indication alerts operators to an operation that, if not strictlyCaution. This indication alerts operators to an operation that, if not strictlyTrademarks. Safety PrecautionsPreface(2)This manual uses the following symbols in the explanations in addition to the warningThis symbol alerts operators to particularly important information. Be sure to read thisThis symbol alerts operators to helpful advice regarding operation. A TRIANGLE symbol indicates that special care and attention is required. The drawing insideA CIRCLE with a diagonal line inside shows action which users may not perform. The drawing inside or under the circle shows the specific action that is not allowed. Outline characters on a colored background show instructions users should follow. It may also include the drawing that shows the specific instruction. Clicking in this icon will play a movie.Trademarks. Safety PrecautionsPreface(3)The screen examples in this manual are subject to change without notice in the interest of productThe screenshots in this manual were captured from the FUJITSU. TWAIN32 scanner driver, ScandAll 21 Image Capturing Utility Software, FUJITSU ISIS scanner. Warning Label. The following picture shows the warning label used in this scanner.

High Temperature. The glass surface insideBe careful not to touchAbout Maintenance. The user must not perform repairs on this scanner. Contact the store where you purchased the scanner or an authorized FUJITSU Image ScannerTrademarks. Safety PrecautionsSafety PrecautionsDo not damage the AC cable. A damaged AC cable may cause fire or electric shock. Do not place heavyDo not use damaged AC cables or power plugs, or install any cables orUse only specified AC cables and connector cables. Use only specified AC cables and connector cables. Failure to use the correct. Use this scanner only at the indicated power voltage. Do not connect to multiple-power strips. Use this scanner only at the indicated power voltage and current. ImproperDo not connect toDo not touch the AC cable with wet hands. Do not touch the power plug with wet hands. Doing so can cause electric shock. Wipe any dust from the power plug. Wipe off any dust from metal parts on the power plug or metal fittings with a soft,Trademarks. Safety PrecautionsSafety Precautions(2)Do not install the scanner in locations subject to oil smoke, steam, humidity, andTurn the scanner OFF if it is damaged. If the scanner is damaged for any reason, turn the scanner off and unplug theDo not put liquids inside the scanner. Do not insert or drop metal objects in to the scanner. Do not scan wetDo not splash or allow theIf foreign objects (water, small metal objects, liquids, etc.) get inside theMaintenance Service Center. Pay particular attention to this warning inDo not touch the inside of the scanner unless necessary. Do not take apart or modify the scanner. The inside of the scanner contains high-Do not use the scanner if there is a strange odor. If you detect heat coming from the device or detect other problems such asMake sure that any smoke coming from it hasTrademarks. Safety PrecautionsSafety Precautions(3)Do not install the scanner on unstable surfaces.

When the scanner is not going to be us ed for a long period of time, be sure to disconnect the power plug fro m the power outlet for safety. Make sure it contains all the parts listed in the package contents list that is included in the package box. Error Recovery Guide is a software that disp lays troubleshooting information on screen when any scanner error occurs. Error Recovery Guide is a software that disp lays troubleshooting information on screen if any scanner error occurs. Error Recovery Guide If you did not install together the Error Recovery Guide with the driver, please proceed with the procedures given below for installing it. Correctly connect the AC cable and the AC adapter. To purchase consumables, conta ct the s tore wh ere you purchased the scanner or an authorized FUJITSU scan- ner service provider. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view. Trademarks. Note, Liability. Preface. Safety PrecautionsIntroduction. Thank you for purchasing the fi-5110C duplex color scanner. Before you start using fi-5110C Duplex Color scanner, be sure to thoroughly read this manual to ensureContents MapTrademarks. Safety PrecautionsRegulatory InformationThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuantThese limits are designed to provide reasonable protection against harmfulThis equipment generates, uses, and can radiate radio frequencyHowever, there is no guarantee that interference will not occur in aIf this equipment does cause harmful interference to radio or television reception,FCC warning. Changes or modifications not expressly approved by the party responsible for compliance could void theThe length of the AC cable must be 2 metersTrademarks.

Safety PrecautionsRegulatory Information(2)This digital apparatus does not exceed the Class B limit for radio noise emissions from digitalCommunications. This Class B digital apparatus complies with Canadian ICES-003. Le pesent appareil numerique n'ement pas de bruits radioelectriques depaassant les limitesCet appareil numerique de la classe B est conformme a la norme NMB-003 du Canada. Hiermit wird bescheinigt, da.It is an open system in which businessThe targeted products are office equipment such asTrademarks. Safety PrecautionsRegulatory Information(3)This product has been designed and manufactured on the assumption that it will be used inThe user should useLIMITED assumes no liability whatsoever for damages arising from use of this product by theAbout the Use of Mercury. Lamp(s) inside this product contain mercury and must be recycled orTo avoid unexpected injury, read the following carefully. Doing the following actions may result in serious personal injuries:Trademarks. Safety PrecautionsTrademarksMicrosoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation in the. ISIS, QuickScan and their respective logos are trademarks or registered trademarks of Pixel. Translations, a division of Captiva Software Corporation in the United States. Adobe, the Adobe logo, and Acrobat are either registered trademarks of Adobe Systems. Other product names are the trademarks or registered trademarks of the respective companies. How Trademarks Are Indicated In This Manual. References to operating systems (OS) and applications are indicated as follows. Where there is no distinction between the different versions of the above operating system, theTrademarks. Safety PrecautionsTrademarks(2)Phone: (81-44) 540-4538. All Rights Reserved, Copyright(C) PFU LIMITED 2004Trademarks.

Make sure that the scanner is installed on a flat, level surface and that none ofDo not installInstall the scanner on a level surface that isInstall the scanner on a strong surface that will support the weight of the scannerDo not block the ventilation ports. Do not block the ventilation ports. Blocking the ventilation ports generates heatDo not place heavy objects or stand on top of the scanner. Do not place heavy objects on the scanner or use the scanner's surface top toFirmly insert the power plug. Firmly insert the power plug as far it can go into the power outlet. Avoid any contact when scanner is in use. Avoid touching any scanner mechanism during scanning since this may causeDo not use the scanner immediately after moving it from aDo not use the device immediately after moving it from a cold place into a warmTrademarks. Safety PrecautionsSafety Precautions(4)Do not move the scanner with the power and interface cables connected as thisBefore moving the scanner, be sure to disconnect the power plug from theMake sure that the floor is free of anyProtect the scanner from static electricity. Install the scanner away from strong magnetic fields and other sources ofDo not use aerosol sprays near the scanner. Do not use aerosol sprays to clean the scanner. Aerosol sprays can blow dirtDisconnect the power plug from the power outlet when theWhen the scanner is not going to be used for a long period of time, be sure toDo not install the scanner in direct sunlight. Do not install the scanner under direct sunlight or near heating apparatus. DoingInstall the scanner in a well-ventilated location.No. Name FunctionNo. Name FunctionNo. NameNo. Name FunctionIndications on the Function Number display. Indication MeaningP Indicates that the scanner has been turned ON and is being initialized.U Indicates that a temporary error occurred when documents were being scanned. A numberE Indicates that a device (hardware) alarm has occurred during scanning of documents.

If this alarm occurs, turn the power off and on again. If the alarm continues after turning theScanningIn this chapter Windows XP screenshots are illustrated. The screens and operations may differ slightly if the OS that you are using is other than Windows XP. Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in thisScanningThe following shows the procedure for turning the scanner ON.The scanner is turned ON, and the green LED on the operator panel lights. Also, while the scanner is being initialized, the indication of the Function Number display changes asScanningThe Power Save mode keeps the scanner in a low-powered state after it has been turned ON. If no operation is performed on the scanner for 15 minutes, the scanner automatically switches to the Power. Save mode. In the Power Save mode, the indication of the Function Number display on the operator panel goes out, butTo return from the Power Save mode, perform one of the following:The scanner will be turned OFF when pressing down the power button for at least two seconds.ScanningConfirm that all the documents have the same width. Check the number of sheets in the document stack. The standard number of sheets that can be loaded on the scanner is as follows:Lightly grip both ends of the document, then bend and fan it. Repeat this operation a couple of times. Rotate the document 90 degrees, then bend and fan it again. Align the edges of the documents.ScanningPull out the ADF paper chute extension according to the length of the document. Extension. Set the documents face-down in the ADF paper chuteLoad the document facing the ADFScanningWhen the document is set on the ADF paper chute the following window mayIn this window, you can select the application program which will perform theScanningMove the side guides so that they touch both sides of the documents.

If there is any space between the side guides and the edges of documents, the scanned image may beSide guidesScanningUse the stacker as follows:HandleIndentationScanningScanningThis starts up ScandAll 21.ScanningScanningFUJITSU TWAIN32 Scanner Driver is designed for scanning documents with FUJITSU image scanner fiThe following describes the procedure with examples of ScandAll 21 for ordinary scanning by using thisStartup the application. Select your scanner on the window below. Load the documents on the scanner. Open the TWAIN Driver window.ScanningMicrosoft Share Point Portal Server.ScanningFor details, refer to the documentation or Help file of your application.Save the scanned images. If you wish to start another scanning, return to procedure 4. End the application.ScanningYou can configure settings for the FUJITSU TWAIN32 Scanner Driver on this window. The following describes the main setting items.ScanningSpecifies the resolution of scanning. It can be specified by selecting a default value from the list or customizing (specify any resolution in 1Scan Type. Specifies the feeding method, the side(s) to be scanned (Front Side, Back Side, Duplex) or details of. Long page (the size of documents longer than A4). Paper Size. Select the size of documents to be scanned from this list.Image Mode. Specifies the image type for the scanned documents. Halftone. Documents are scanned through halftone processing in black andGrayscale. Documents are scanned in gradations from black to white. For thisColor. Documents are scanned in color. For this mode, you can select 24Starts scanning documents with the current settings.ScanningYou can confirm the image of the documents in the preview window. Saves the current settings and closes this window. Used to undo changes of settings.Opens an information window about the FUJITSU TWAIN32 Scanner Driver's version.ScanningSelect this tab when setting image rotation, detection of document size, etc.

Select this tab when setting cache mode, multi feed detection, blank page skipping, etc. Select this tab to change the unit displayed on the Setting Window for the FUJITSU TWAIN32. Scanner Driver. (Millimeters, Inches, and Pixels are available). Select this tab for setting the Scanner Operation Panel. Select this tab for setting the image processing filter(s). Page Edge Filler: Fills up the margins of the scanned documents with a selected color. Digital Endoser: A character string, such as the alphabet and numbers, can be added in the scannedSelect this tab for setting the compression rate of JPEG Transfer.ScanningYou can set Edge Extract, Gamma Pattern, White Level Follower, Dropout Color, Reverse, etc. Click this button for configuring the Setting Files. You can save the changed settings as a Setting File. From next scanning, the settings are quicklyScanningFUJITSU ISIS Scanner Driver is designed for scanning documents with FUJITSU image scanner fi series byThe following describes the procedure with examples of QuickScan for ordinary scanning by using this driverThe procedure may vary depending on your application. If you use an application other than QuickScan,Startup the application. Select your scanner on the window below.ScanningA new profile will be created based on the profile you selected.The settings of the selected profile can be changed.Select one from the already existing profiles. Scanning will be started according to the settings of the selected profile. Go to procedure 9. The configuration window of ISIS driver appears.ScanningScanned images are displayed on the window.After the installation of QuickScan, it is registered inScanningImage Mode. Select a color mode suitable for the purpose from the menu. Scans data in binary (black and white). Distinguishes black from white accordingThis scanningScans data by 14 shades of gray plusScans data by 254 shades of gray plusScans data as full-colored image usingImage Processing.

Binary processing is applied to theOption (separately sold) is installed.Resolution. Specifies the number of pixels (dots) per inch. Select a fixed resolution from the list or enter any value (from 50 to 600) manually. A higher resolution produces finer image, but requires much more memory.ScanningSelect the halftone pattern for halftone scanning. Dither Pattern. This setting is suitable for scanningDither Pattern 1. This setting is suitable for scanningDither Pattern 2. This setting is suitable for scanningDither Pattern 3. This setting is suitable for scanningError Diffusion. This function minimizes differencesThis mode is suitable for scanningDownload. Executes processing with theBrightness. Sets the brightness of the entire image. Specify the brightness as a number within theTo brighten the entire image, increase the value ofContrast. Sets the contrast between light and shadow of the scanned image. Specify theScanningSelects the scanning method. ADF (Front Side). Scans only the front sides ofADF (Back Side) Scans only back sides of documents. ADF (Duplex). Scans both front and the back sidesPaper Size. Selects a paper size according to the size of the document to be scanned. Select aPage Layout. Specifies orientation of the documents as portrait or landscape.ScanningSpecify scan area for the document size. The size can be set by dragging the frame with mouse. Otherwise, enter any value for the setting. Opens the JPEG Settings dialog box. Used for setting the compression rate of JPEGThis button displays the version information.ScanningDTC Variance. This option specifies the value for adjusting the variance based on the brightness of theEdge Processing. This option specifies the sharpness of contour extraction. Low, Mid, High. Emphasizes contour of images. AvailableSmoothing Smoothes jaggy images. Dropout Color. This option excludes selected color (the three primary colors of light i.e. green, red, blue)Reverse. Colors of scanned images are reversed.